![]() |
![]()
![]() |
![]() |
#1 |
![]() Drives: Yaris 2010 sedan // 1993 Miata Join Date: Jun 2016
Location: Florida
Posts: 4
|
Any intake manifolds??
I’ve been looking all over the forums and didn’t see much... anybody have any info on any intake manifolds that would fit a 2010 Yaris sedan (1nz-fe) again I couldn’t find much I found one guy that said he use to sell some but that’s pretty much it.
Thank you |
![]() |
![]() |
![]() |
#2 | |
![]() ![]() ![]() Drives: MR2 Spyd/Type R/Yaris/Civic Si Join Date: Feb 2007
Location: Ottawa
Posts: 479
|
Quote:
I've got one called the Tooter (but I'm not sure he makes them anymore which is a shame) , there was another one made by GoldenEagle? and I think MicroImage made one while they were still around.
__________________
https://www.instagram.com/3cyltrbo/ |
|
![]() |
![]() |
![]() |
#3 |
![]() ![]() ![]() ![]() ![]() ![]() ![]() Drives: '14 GT86, '08 Vitz Join Date: Dec 2006
Location: Central Valley, CA
Posts: 9,873
|
Had a Tooter in my first Yaris. Definitely felt a torque increase/power band shift, which was great for daily driving. Also increased my mpg. Wish he still made them so I can put one in my (second) Yaris now.
|
![]() |
![]() |
![]() |
#4 |
daily driver
|
![]()
__________________
![]() |
![]() |
![]() |
![]() |
#5 |
![]() ![]() ![]() ![]() ![]() Drives: 2007 yaris 3 door Join Date: Sep 2015
Location: Denver, Colorado
Posts: 1,000
|
aftermarket or a stock unit?
i can look for one in my local pull-and-pay. i can also port it out properly if needed. |
![]() |
![]() |
![]() |
#6 |
![]() ![]() ![]() ![]() |
One was designed but never made it to production.
MicroImage then collaborated with Golden Eagle to have some made. MicroImage no longer has a "storefront" and I don't think any of those are being sold anymore. Unless you find them used. |
![]() |
![]() |
![]() |
#7 |
![]() ![]() Drives: |Mr2 Join Date: Feb 2018
Location: Edmonton, Alberta
Posts: 55
|
its a 50% off weekend at my local wrecker, so i'm going to pull a corolla manifold, see if i can cut n paste, plastic weld, and match it to a 1nz flange. , bigger throttle, plenum volume and cheap. just elbow grease...
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
DIY: Intake Installation | redyaris | DIY / Maintenance / Service | 53 | 08-23-2014 05:34 AM |
tooter's manifold adventure... | tooter | Performance Modifications | 1465 | 07-31-2014 08:11 PM |
Performance intake manifolds | pwisenbaker | Performance Modifications | 44 | 06-21-2011 06:01 PM |
The great intake debate! | fmicle | General Yaris / Vitz Discussion | 74 | 10-06-2009 11:37 PM |
Intake Systems Decision Maker.. | Blenjar | Performance Modifications | 25 | 09-15-2007 10:07 PM |