Retorque ARP head studs turbo build - Toyota Yaris Forums

nomad · 08-12-2019, 05:04 PM

Hi guys first post in here. Need some help.
Anyone know if I can retorque ARP head studs
Without removing the camshafts on 1nzfe?
Just about finished run in for new build and
Will need to retorque but don't know if cams need to
Be removed. All I know is that arp head studs are
Made so that they can be retorqued without needing to
Remove camshafts but unsure on our engines.

Thanks in advance for your help!

Jason@SportsCar · 08-12-2019, 07:19 PM

Cams are in the way of the head bolts. We also found we could not use a complete set of ARP studs because the bolts they include are so tall they hit the CAM timing wheel and block the VVTi passage, so we mix them with OE bolts.

nomad · 08-13-2019, 04:08 AM

Great thanks for your help Jason.

Tima122 · 08-15-2019, 07:38 PM

1. Потребуется немного сточить клапан vvt-i, потому что шпильки ARP больше в диаметре.
2. Потребуется уменьшить диаметр впускного вала у первой крышки распредвала. Так как гайка ARP слишком высокая.
3. Для замены стандартных болтов крепления головки блока цилиндров распредвалы снимать обязательно.

Zedicus · 06-24-2020, 04:56 PM

the 1nz ARP kit needs 3 of the nuts ground down too fit.
ALSO you will need to notch the end off of the VVT-i solenoid as it hits one of the nuts.

cut the side of the nut where the socket goes, NOT the side that makes contact with the head.

i did not want to use the OEM spring bolts mixed with the ARP as they would apply different amount of load. cutting the top off the nut does not change any properties affecting torquing or loading on the build.

the ones that go here need about 1/8" cut off the TOP of the nut. otherwise they hit the cam.

levanarosGR · 11-30-2021, 04:57 AM

Hello guys, can you give me some more specific information about how to notch the solenoid valve without damaging it?

08-12-2019, 05:04 PM	#1
nomad Drives: 2005 Toyota Vitz RS Join Date: May 2018 Location: New Zealand Posts: 2	Retorque ARP head studs turbo build Hi guys first post in here. Need some help. Anyone know if I can retorque ARP head studs Without removing the camshafts on 1nzfe? Just about finished run in for new build and Will need to retorque but don't know if cams need to Be removed. All I know is that arp head studs are Made so that they can be retorqued without needing to Remove camshafts but unsure on our engines. Thanks in advance for your help!

08-12-2019, 07:19 PM	#2
Jason@SportsCar Drives: 2015 H Production Yaris Join Date: Oct 2009 Location: Debary, FL Posts: 1,953	Cams are in the way of the head bolts. We also found we could not use a complete set of ARP studs because the bolts they include are so tall they hit the CAM timing wheel and block the VVTi passage, so we mix them with OE bolts. __________________ 2005-2008 SCCA Solo BS National Champion 2017-2018 SCCA H Prod National Champion

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Want to build costom turbo kit. Need advice from boosted guys!	pimp my yaris	Forced Induction Forum	639	09-28-2013 12:26 PM
Chevy Aveo RS: Turbo + good looks = build it!	Thirty-Nine	Off-topic / Other Cars / Everything else Discussions	22	01-12-2010 01:36 PM
Turbo Project Yaris TS 1.8L	CASTREX	Yaris TS Talk	40	08-21-2009 11:24 AM
build up for a turbo	redduck	Forced Induction Forum	15	07-02-2007 10:31 PM
turbo manifold build...	joey1320	Forced Induction Forum	4	06-30-2007 03:26 PM

08-13-2019, 04:08 AM	#3
nomad Drives: 2005 Toyota Vitz RS Join Date: May 2018 Location: New Zealand Posts: 2	Great thanks for your help Jason.

08-15-2019, 07:38 PM	#4
Tima122 Drives: bB NCP 31 2005 y Join Date: May 2011 Location: KHABAROVSK RUSSIA Posts: 19	1. Потребуется немного сточить клапан vvt-i, потому что шпильки ARP больше в диаметре. 2. Потребуется уменьшить диаметр впускного вала у первой крышки распредвала. Так как гайка ARP слишком высокая. 3. Для замены стандартных болтов крепления головки блока цилиндров распредвалы снимать обязательно.

06-24-2020, 04:56 PM	#5
Zedicus Drives: scion xb Join Date: Apr 2020 Location: SW KS Posts: 26	the 1nz ARP kit needs 3 of the nuts ground down too fit. ALSO you will need to notch the end off of the VVT-i solenoid as it hits one of the nuts. cut the side of the nut where the socket goes, NOT the side that makes contact with the head. i did not want to use the OEM spring bolts mixed with the ARP as they would apply different amount of load. cutting the top off the nut does not change any properties affecting torquing or loading on the build. the ones that go here need about 1/8" cut off the TOP of the nut. otherwise they hit the cam.

11-30-2021, 04:57 AM	#6
levanarosGR Drives: yaris ts 2005 Join Date: Jul 2018 Location: greece Posts: 2	Hello guys, can you give me some more specific information about how to notch the solenoid valve without damaging it?