|
05-22-2007, 12:49 PM | #109 |
Banned
Drives: LB Join Date: Jul 2006
Location: OH
Posts: 7,787
|
You have to remember, it is a part that may be spinning at thousands of RPM's when it fails, turning it into a bonafide Dreidel of ultimate despair! I'll bet the side of his block is all jacked up too!
Not a part to skimp on if you ask me. |
05-22-2007, 02:09 PM | #110 |
Super Moderator
|
OK... I guess I'm convinced. Now all I need to know is wether I should wait for the pulley set to come out or not. Sure, I understand that it's better to support our vendors ASAP so they can come out with products sooner and allathat, but I'm kinda wary about messing with the motor too many times.
I would much rather install the whole set once and be done with it.
__________________
--[ FORUM RULES ]--[ SEARCHING TIPS ]--[ EYELIDS PICS ]--[ RBK SPOILER ]--[ BEST/WORST INVESTMENTS ]--
|
05-22-2007, 02:58 PM | #111 |
Drives: 2007 Yaris HB Join Date: Apr 2007
Location: my own little world
Posts: 1,256
|
|
05-22-2007, 09:31 PM | #112 |
Drives: 07 Yaris Join Date: Mar 2007
Location: AZ, USA
Posts: 114
|
Installed mine today and the first thing I noticed was that it idles at higher RPMs than it did.
I didn't notice the idle being rough. It does seem like the shift is smoother now (AT). |
05-31-2007, 02:18 PM | #113 |
Banned
Drives: LB Join Date: Jul 2006
Location: OH
Posts: 7,787
|
NST @ SCION EXPO 2007
scionexpoFlyer.jpg Expo7NST1.jpg Expo7NST2.jpg Expo7NST4.jpg Expo7NST5.jpg Expo7NST8.jpg Expo7NST10.jpg Expo7NST11.jpg |
06-02-2007, 03:46 PM | #114 |
ULTIMATE
Drives: 07 Yaris Turbo Join Date: May 2007
Location: Canoga Park, CA
Posts: 14,859
|
ok, I'm in!
Just ordered from Dezod.... hope you have red, 'cause the website didn't say "no".... |
06-03-2007, 03:30 AM | #115 |
37HSSV
|
I will be definatly ordering the full set, (Crank/WP/Alt.) pulleys when they come out, Red all the way.
Do we estimate how much HP we will get with the full set?
__________________
07 Toyota Yaris Hatchback -sold- 11 Mazdaspeed 3 -SRI/TIP, 3 inch TBI, Custom FMIC, Tuned by Cobb Accessport, HKS ssq2 BOV, Upgraded HPFP- Clean stock look... Killer performance. |
06-03-2007, 06:00 AM | #116 |
Drives: 2007 Yaris S Join Date: May 2007
Location: Piqua, Ohio
Posts: 302
|
I was looking at the pullies in my car the other day while changing oil. How hard is a pully set to install? It looked reeeeeal tight in there. I don't think I could fit my big dickbeaters in there to do it.
|
06-03-2007, 07:51 AM | #117 | |
Super Moderator
|
Quote:
http://www.yarisworld.com/forums/showthread.php?t=3964 Good luck!
__________________
--[ FORUM RULES ]--[ SEARCHING TIPS ]--[ EYELIDS PICS ]--[ RBK SPOILER ]--[ BEST/WORST INVESTMENTS ]--
|
|
06-04-2007, 08:09 PM | #118 |
is it going to be less expensive to buy it in a set or its the same to buy it appart;..
|
|
06-05-2007, 07:04 AM | #119 |
Drives: yaris Join Date: Mar 2007
Location: HK
Posts: 14
|
does the pulley work on other car with 1nz FE engine?
my dad also want to get one for his corolla with 1nz fe engine |
06-05-2007, 11:43 AM | #120 |
Down With the Sickness
|
arent the corolla's powered by 1zz fe's? but the asian corolla is 1.6L
__________________
Strength - Determination - Merciless - Forever |
06-06-2007, 03:00 AM | #121 |
Down With the Sickness
|
bump, i want my alt. and water pump pulley already
with nst quickshifter
__________________
Strength - Determination - Merciless - Forever |
06-06-2007, 07:19 AM | #122 | |
Drives: yaris Join Date: Mar 2007
Location: HK
Posts: 14
|
Quote:
http://toyota.com.hk/showroom/corolla_cbu/index.html |
|
06-06-2007, 01:54 PM | #123 |
ULTIMATE
Drives: 07 Yaris Turbo Join Date: May 2007
Location: Canoga Park, CA
Posts: 14,859
|
I am told these are back ordered until July 1.... boo!
I'll wait tho....would never ever order "that other company's" pulley |
06-06-2007, 02:20 PM | #124 | |
Down With the Sickness
|
Quote:
__________________
Strength - Determination - Merciless - Forever |
|
06-06-2007, 05:24 PM | #125 |
Drives: NST CARS: S13 AE86 ANT10 AW11 Join Date: Dec 2006
Location: USA
Posts: 1,097
|
Hi again everyone,
Wow, it looks like there has been a lot of good discussion here lately. This is turning into a very productive thread with some great information. Here is a little info regarding fitment on the 1.5, 1.3, Yaris, Corolla, etc. There are two versions of the 1NZ crank pulley... One version, on cars with NO power steering pulley, is a SINGLE-ROW Crank Pulley. Example: USDM Toyota Yaris 1NZFE... Just one row there... Another version, on cars equipped with a power steering pulley, is a TWO-ROW Crank Pulley. Example: Scion xA and xB 1NZFE... See the two rows there? Those of you with a USDM Yaris, and those internationally who have SINGLE-ROW Crank Pulleys can order pulleys from our Yaris page on our site... http://www.nonstoptuning.com/pKitToyYarisPics.htm Those of you internationally, and those with TWO-ROW Crank Pulleys can order pulleys from our Scion xA page on our site... http://www.nonstoptuning.com/pKitToySciXAXB.htm As always, thank you for all your support and enthusiasm. I don't post on any other forums, but I really do enjoy visiting your forums from time to time Last edited by NonStopTuning; 06-06-2007 at 08:53 PM. |
06-06-2007, 06:29 PM | #126 |
ULTIMATE
Drives: 07 Yaris Turbo Join Date: May 2007
Location: Canoga Park, CA
Posts: 14,859
|
can you confirm that they are back ordered until July 1?
|
|
|