|
09-01-2015, 11:25 PM | #1 |
Drives: 2006 Toyota Vios NCP42 Join Date: Sep 2015
Location: Singapore
Posts: 6
|
1nz-fe high compression setup [build]
Hi everyone, I'm Ben from Singapore
I'm driving a Vios NCP42, which is powered by the same 1nz-fe engine as the Yaris (well, except for the head which is different, as I learnt the hard way) I'm currently building a high compression setup for my car and I'm writing about the build on my blog, POWAA Garage. just felt like sharing it with everyone, and see if anyone has comments, questions or even better, recommendations for me. This is my first engine build, so I still have a lot to learn! here's the link to the first part of the build: http://www.powaagarage.com/2015/08/P...ld-Part-I.html !!-------------------------------!!-------------------------------!!-------------------------------!!-------------------------------!! Part 2 is out! We bring the engine together! Enjoy the read: http://www.powaagarage.com/2015/10/P...d-Part-II.html Part 3 will come out soon!
__________________
Check out my website: http://www.powaagarage.com/ Representing the car culture in Singapore! Last edited by POWAA; 10-09-2015 at 03:05 AM. |
10-02-2015, 07:34 AM | #2 |
Drives: 2007 Yaris Join Date: Aug 2014
Location: Winnipeg, canada
Posts: 59
|
Looking forward to the rest of the article. Good luck on your build
|
10-02-2015, 11:53 AM | #3 | |
Drives: 2015 H Production Yaris Join Date: Oct 2009
Location: Debary, FL
Posts: 1,953
|
Quote:
Seems pretty clear these were never properly test fitted when ARP designed the kit.
__________________
2005-2008 SCCA Solo BS National Champion 2017-2018 SCCA H Prod National Champion |
|
10-09-2015, 03:03 AM | #4 |
Drives: 2006 Toyota Vios NCP42 Join Date: Sep 2015
Location: Singapore
Posts: 6
|
@Crazylegs
Thanks man! appreciate the support @Jason we indeed had a few issues with one of the bolts, the one on cylinder 1 admission side was messing things up as you said, so we had no choice but to leave the stock one for this bolt... Nice Yaris BTW! where do you race it?
__________________
Check out my website: http://www.powaagarage.com/ Representing the car culture in Singapore! |
10-09-2015, 03:05 AM | #5 |
Drives: 2006 Toyota Vios NCP42 Join Date: Sep 2015
Location: Singapore
Posts: 6
|
Part 2 is out! I updated the first post, but here's the link again just in case:
http://www.powaagarage.com/2015/10/P...d-Part-II.html Enjoy!
__________________
Check out my website: http://www.powaagarage.com/ Representing the car culture in Singapore! |
10-09-2015, 10:19 AM | #6 |
Drives: '08 2zr swapped Vios M/T Join Date: Oct 2012
Location: Caledonia Ont.
Posts: 2,938
|
I'm enjoying the blog man. What did you use to increase the compression? Did you go with a longer piston rod or shave down the cylinder head?
__________________
No one ever wants to give a Yaris the point by... |
10-09-2015, 12:12 PM | #7 | |
Drives: 2015 H Production Yaris Join Date: Oct 2009
Location: Debary, FL
Posts: 1,953
|
Quote:
We run the car in SCCA Club Racing. Just got back from Daytona for the SCCA National Championship Runoffs where we got to race on the Rolex 24 course. Got the pole, but finished second in a NASCAR worthy pileup at the end: http://www.scca.com/videos/1972492
__________________
2005-2008 SCCA Solo BS National Champion 2017-2018 SCCA H Prod National Champion |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
***The Engine Oil Bible*** | Hussain-Vtec | Performance Modifications | 20 | 09-28-2016 02:47 PM |
NEED ENGINE CHECK LIGHT CODE LIST | Attitude | Forced Induction Forum | 12 | 04-11-2011 06:38 PM |
Yaris sedan low and high beam | jorizk | DIY / Maintenance / Service | 10 | 03-02-2010 09:49 AM |
The last gas question | Tonavi | DIY / Maintenance / Service | 56 | 04-27-2009 08:40 PM |
High compression engine | flow-vitz | General Yaris / Vitz Discussion | 1 | 11-15-2006 01:03 PM |