![]() |
![]()
![]() |
|
![]() |
#1 |
![]() ![]() Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
![]()
Is there special tool to install dust boot cover ring on ball joint?
|
![]() |
![]() |
![]() |
#2 |
![]() ![]() Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
:(
|
![]() |
![]() |
![]() |
#3 |
![]() ![]() Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
This happened after using ball joint fork
![]() |
![]() |
![]() |
![]() |
#4 |
![]() ![]() Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
.
|
![]() |
![]() |
![]() |
#5 |
![]() ![]() ![]() ![]() ![]() ![]() ![]() Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Did you rip the new boot by trying to use the for to get that ring on?
I would probably try two pairs of locking pliers to hold the ends while pulling them apart to get the clip into place. There is a special tool for spreading that type of clip, but it may not be something that you could get from a local autoparts store.
__________________
![]() |
![]() |
![]() |
![]() |
#6 |
![]() ![]() ![]() Drives: Prius C Join Date: Feb 2013
Location: US
Posts: 240
|
What Scott said. There are some special pliers. I've gotten them from sears before. Craftsman.
|
![]() |
![]() |
![]() |
#7 |
![]() ![]() Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
|
![]() |
![]() |
![]() |
#8 |
![]() ![]() ![]() ![]() ![]() ![]() Drives: 08 Yaris Sedan Join Date: Oct 2008
Location: California - Bay Area
Posts: 2,773
|
I hate using pickle forks on the ball joint it always garentees you will damage the boot. This is the actual tool and brand I keep in my tool box for this job
http://www.youtube.com/watch?v=7vweCmGwBiU Its about 20 bucks at harbor freight or around 50 for the entire master kit.
__________________
|
![]() |
![]() |
![]() |
#9 | |
![]() ![]() Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
Yep I used that to remove it after fork failed
Quote:
|
|
![]() |
![]() |
![]() |
#10 |
![]() ![]() Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
No, that's old stock boot and new one still good. I tried to spread using two locking pliers but it doesn't spread enough to fit. Looks like i need special tool
|
![]() |
![]() |
![]() |
#11 |
![]() ![]() Drives: 07 BB yaris / 06 Mustang Gt Join Date: Apr 2007
Location: northern california
Posts: 136
|
Can I use this to lubricate ball joint?? Thank you
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Clazzio Seat Cover DIY Install | PETERPOOP | DIY / Maintenance / Service | 31 | 09-10-2010 03:30 PM |
Ball Joint on Bottom Arm | David Godfrey | DIY / Maintenance / Service | 1 | 04-18-2010 06:27 PM |
DIY Needed removal of entire e brake boot cover if it is possible? | YarisSedan | DIY / Maintenance / Service | 5 | 12-18-2009 05:23 AM |
07-08 Shift boot and ring | schleppy | Willing to Buy by private party | 13 | 11-30-2009 03:06 AM |