N/A setup - Page 2 - Toyota Yaris Forums

lilredrocket · 10-06-2009, 09:30 PM

Tamago didn't you look up the piston part number and they were different?

thebarber · 12-07-2009, 12:33 AM

i think its 2" from the header to the backside of the resonator....then it goes down to 1.75"

i had a megan axleback when i had the midpipe done, so ya, they built me a pipe with a new flange to attach to the axle back (any axleback)

advocate · 12-07-2009, 01:10 AM

Awesome that's what I wanted to know. Thanks for the help.

sujonol78 · 12-07-2009, 04:24 AM

hi there. i came across this forum when i was browsing for some parts for my 1NZ-FE ( Toyota Vios ). Since we are using the same engine, i thought we could share some of our experiences.

My name is Sujono, M, 32 y/o from Jakarta, Indonesia.
here's what I do with my 1nz-fe:
JFC air filter
Intake induction system
TRD clutch and clutch cover
Apexi Neo
CamCon
Custom exhaust manifold ( straight type, about 3mm larger than the standard one, 4:1 )
Custom muffler

with the Apexi Neo and CamCon working together, I can easily control the AFR and the timing.

dyno test ( without camcon and custom exhaust manifold ): 173Nm ( 4500 RPM ) & 132BHP ( 6000 RPM ).

looking forward to have a good discussion on how to improve our 1nz-fe performance ;)

cheers

10-06-2009, 09:30 PM	#1
lilredrocket Slowy getting there View User's Garage Drives: 08 Liftback Join Date: Nov 2008 Location: DFW, Texas Posts: 1,464	Tamago didn't you look up the piston part number and they were different? __________________

12-07-2009, 12:33 AM	#2
thebarber daily driver View User's Garage Drives: the #wrecho Join Date: Jun 2006 Location: Grand Rapids, MI Posts: 5,877	i think its 2" from the header to the backside of the resonator....then it goes down to 1.75" i had a megan axleback when i had the midpipe done, so ya, they built me a pipe with a new flange to attach to the axle back (any axleback) __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My suspension setup: Breakfast Blend for the angry panda	Tamago	Wheels, Tires and Suspension Forum sponsored by The Tire Rack	57	07-26-2010 04:56 PM
Warranty Information for US Yaris Owners	AdeJong 03	General Yaris / Vitz Discussion	4	09-19-2009 11:14 PM
Works bell/Nardi quick release steering wheel setup	blacksandiegovitz	Cosmetic Modifications (Exterior/Interior)	35	09-02-2009 06:52 PM
good speaker setup.	ryota	In Car Entertainment + Electronics (audio / video / alarm)	18	08-08-2009 08:46 PM
Suspension Setup Question	Ran Kizama	Wheels, Tires and Suspension Forum sponsored by The Tire Rack	27	04-28-2007 03:05 PM

12-07-2009, 01:10 AM	#3
advocate Drives: car Join Date: Oct 2008 Location: location Posts: 1,033	Awesome that's what I wanted to know. Thanks for the help.

12-07-2009, 04:24 AM	#4
sujonol78 Drives: 1nz-fe / MT Join Date: Dec 2009 Location: Indonesia Posts: 26	hi there. i came across this forum when i was browsing for some parts for my 1NZ-FE ( Toyota Vios ). Since we are using the same engine, i thought we could share some of our experiences. My name is Sujono, M, 32 y/o from Jakarta, Indonesia. here's what I do with my 1nz-fe: JFC air filter Intake induction system TRD clutch and clutch cover Apexi Neo CamCon Custom exhaust manifold ( straight type, about 3mm larger than the standard one, 4:1 ) Custom muffler with the Apexi Neo and CamCon working together, I can easily control the AFR and the timing. dyno test ( without camcon and custom exhaust manifold ): 173Nm ( 4500 RPM ) & 132BHP ( 6000 RPM ). looking forward to have a good discussion on how to improve our 1nz-fe performance ;) cheers