DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag - Page 12 - Toyota Yaris Forums

CTScott · 10-31-2009, 08:18 AM

Quote:

Originally Posted by sabya78

I installed the CC, when I switch it on the speedometer jumps once , pressing the set buttom dosen't set the speed . While installing , by mistake I connected the 12 V supply instead of the ground which stalled the engine immediately . Can anyone help me if I have screwed up the CC function of my ECU. The car is running fine otherwise.

So far it looks like only US and Canada Yaris have the cruise functionality built into the ECM. In the UAE do you get European Yaris? If so, cruise is definitely not built in.

sabya78 · 11-01-2009, 04:09 AM

Dear Scott,

Thanks for the update .. I dont think the Yaris in the UAE is European.. I checked up the VIN and it states my car is made in Japan and is ment for the GCC market. I was really looking forward to install the CC ,, is there any other way to do it or any how can I check if the ECU is having the CC function?

CTScott · 11-01-2009, 08:52 AM

Quote:

Originally Posted by sabya78

Dear Scott,

Thanks for the update .. I dont think the Yaris in the UAE is European.. I checked up the VIN and it states my car is made in Japan and is ment for the GCC market. I was really looking forward to install the CC ,, is there any other way to do it or any how can I check if the ECU is having the CC function?

First, make sure that you are really in pin 40 of the ECM.

Second, what is the part number on the label of your ECM?

SEALL · 11-03-2009, 08:45 AM

Quote:

Originally Posted by CTScott

Maybe you should buy a USDM ECM off ebay. Then, you'll have the only Yaris in China with cruise control.

hahahaha~~~good idea！but how much the USDM ECM? and I need to change the ECU or ECM's Program? or install it directly into the in-situ and do not change anything?

CTScott · 11-03-2009, 08:51 AM

Quote:

Originally Posted by SEALL

hahahaha~~~good idea！but how much the USDM ECM? and I need to change the ECU or ECM's Program? or install it directly into the in-situ and do not change anything?

I'm not sure about the compatibility, but USDM ECMs can often be purchased for under $100 off ebay. The engine type, transmission type, ABS yes/no, and VSC yes/no are important to match when swapping ECMs. Our USDM ECMs are for 1NZFE and 2NZFE engines. I haven't noticed which engine you get over there.

SEALL · 11-03-2009, 10:18 PM

My yaris's engine is 4ZRFE,1600cc,Super ECT 4-speed AT,ABS yes,VSC no,maybe only have the 1600cc engines of the Chinese market.

CTScott · 11-03-2009, 11:01 PM

Quote:

Originally Posted by SEALL

My yaris's engine is 4ZRFE,1600cc,Super ECT 4-speed AT,ABS yes,VSC no,maybe only have the 1600cc engines of the Chinese market.

I think you are correct. Are you able to see the part number label on your ECM?

rtom · 11-03-2009, 11:06 PM

Anybody know about relevant wiring in 2010 liftbacks?

I'd like to try this on a 2010 2-door base liftback purchased in the US!

CTScott · 11-03-2009, 11:13 PM

Quote:

Originally Posted by rtom

Anybody know about relevant wiring in 2010 liftbacks?

I'd like to try this on a 2010 2-door base liftback purchased in the US!

2010 is identical to 2009 for the DIY cruise mod.

SEALL · 11-04-2009, 09:49 AM

Quote:

Originally Posted by CTScott

I think you are correct. Are you able to see the part number label on your ECM?

I don't know what's the part number,I saw the lable on my ECM,there are some number on it:89661-0DA20 ; TD275100-9872 ; C90.

CTScott · 11-04-2009, 11:18 AM

Quote:

Originally Posted by SEALL

I don't know what's the part number,I saw the lable on my ECM,there are some number on it:89661-0DA20 ; TD275100-9872 ; C90.

89661-0DA20 is the part number. It looks like it is a China specific ECM.

SEALL · 11-05-2009, 01:17 AM

It seems useless to put on a USDM ECM.

CTScott · 11-05-2009, 08:03 AM

Quote:

Originally Posted by SEALL

It seems useless to put on a USDM ECM.

Agreed. I don't think it would be compatible with your engine.

SEALL · 11-05-2009, 09:58 AM

Quote:

Originally Posted by CTScott

Agreed. I don't think it would be compatible with your engine.

Although there is no success, but very grateful to you for your help,And your very pleasant exchanges.

sabya78 · 11-08-2009, 06:28 AM

Quote:

Originally Posted by CTScott

So far it looks like only US and Canada Yaris have the cruise functionality built into the ECM. In the UAE do you get European Yaris? If so, cruise is definitely not built in.

The part number on my ECM is 89661-52C00

CTScott · 11-08-2009, 08:55 AM

Quote:

Originally Posted by sabya78

The part number on my ECM is 89661-52C00

I would say that there is a good chance that that ECM doesn't have cruise control, as that part number is not a USDM/CAN one and so far it appears that just ECMs for those markets have the functionality. One test that you can try is to measure the voltage on pin 40 of the ECM connector A21, with the connector in and the ignition in the ON position. If you measure +12VDC to ground on that pin, then there is a good chance that your ECM supports cruise. If you measure 0 VDC to ground, then it definitely does not.

t2mike2 · 01-14-2010, 10:00 PM

Hi guys im new here , joined because im getting my yaris tomorrow and was intrigued by this mod.

Can someone show me with microsoft paint maybe, how i can wire up this switch?

http://www.alliedelec.com/search/pro...px?SKU=9485541

~mkie~

t2mike2 · 01-14-2010, 10:17 PM

Quote:

Originally Posted by nickhjort

TDB-1, to jump the switch connector, you simply put a wire from one terminal to the other (the switch plug only has 2 terminals right)? You didn't put a fuse or anything in there just in case?

Where is the switch connector ?

01-14-2010, 10:00 PM	#215
t2mike2 Drives: '10 Yaris 3 DR - Carmine Red Join Date: Jan 2010 Location: Lorton VA Posts: 10	help? Hi guys im new here , joined because im getting my yaris tomorrow and was intrigued by this mod. Can someone show me with microsoft paint maybe, how i can wire up this switch? http://www.alliedelec.com/search/pro...px?SKU=9485541 ~mkie~

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
OEM foglight switch and leather wrap steering wheel	808yarisLB	Cosmetic Modifications (Exterior/Interior)	8	03-11-2009 01:05 AM
SCION SPORT STEERING WHEEL, RED, XA AND XB, 03 TO 06	justoneyaris	Items for Sale by private party	3	12-04-2008 07:30 PM
steering wheel setup	aucorium	Cosmetic Modifications (Exterior/Interior)	0	07-24-2007 02:05 AM
How do you take off steering wheel	mrrock	Cosmetic Modifications (Exterior/Interior)	3	12-05-2006 11:16 AM

11-01-2009, 04:09 AM	#200
sabya78 Drives: Yaris Join Date: Jul 2009 Location: UAE Posts: 3	Dear Scott, Thanks for the update .. I dont think the Yaris in the UAE is European.. I checked up the VIN and it states my car is made in Japan and is ment for the GCC market. I was really looking forward to install the CC ,, is there any other way to do it or any how can I check if the ECU is having the CC function?

11-03-2009, 10:18 PM	#204
SEALL Drives: 08’Yaris Join Date: Oct 2009 Location: China Posts: 10	My yaris's engine is 4ZRFE,1600cc,Super ECT 4-speed AT,ABS yes,VSC no,maybe only have the 1600cc engines of the Chinese market.

11-03-2009, 11:06 PM	#206
rtom Drives: 2010 Yaris 3-door liftback MT Join Date: Nov 2009 Location: Denver, CO Posts: 47	Anybody know about relevant wiring in 2010 liftbacks? I'd like to try this on a 2010 2-door base liftback purchased in the US!

11-05-2009, 01:17 AM	#210
SEALL Drives: 08’Yaris Join Date: Oct 2009 Location: China Posts: 10	It seems useless to put on a USDM ECM.