|
05-02-2009, 06:15 PM | #181 |
My R1 eats my Vitz!!
Drives: '07 Vitz Lifty, Stick Shift Join Date: May 2007
Location: Oneida, NY
Posts: 131
|
Thank you so much, I have about 3 hours before the sun light is bye bye. It wasn't too hard to remove the top. Couple scratches and bruises on my hands, but now that I know how, of course, I can do it a lot quicker next time.
__________________
My Car Rules! |
05-02-2009, 06:23 PM | #182 |
My R1 eats my Vitz!!
Drives: '07 Vitz Lifty, Stick Shift Join Date: May 2007
Location: Oneida, NY
Posts: 131
|
I'm not the best at reading wiring diagrams, but from what I can see my car doesn't even have this "ad4 plug" see picture...
And I can't find a plug hanging down that would plug into the Clutch Switch for Cruise Control. I can see where the switch mounts to the Clutch Pedal Mount...but no plug. Please help me :(
__________________
My Car Rules! Last edited by nickhjort; 05-02-2009 at 06:36 PM. |
05-02-2009, 06:40 PM | #183 |
My R1 eats my Vitz!!
Drives: '07 Vitz Lifty, Stick Shift Join Date: May 2007
Location: Oneida, NY
Posts: 131
|
Also if this is the case, does that mean my ECU doesn't even have the Cruise control programmed into it, so I can't tap a wire right from the ECU itself? I hope I can do this...seeing as I already drilled my holes and put switches :) (kicks self for not getting priorities straightened out before starting project...1. Check to see if this will work...2. Then cut $hit up HAHAHA!! Not the other way around...)
__________________
My Car Rules! |
05-02-2009, 07:18 PM | #184 |
Drives: '08 5-door Join Date: Apr 2009
Location: Surrey, BC Canada
Posts: 176
|
I think you're right, especially since the factory diagram has a note saying "gray" on the picture of the AD4 plug.
Last edited by Sir A.Y. Atoyot; 07-27-2010 at 05:01 PM. |
05-02-2009, 07:49 PM | #185 |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
It is definitely the grey next to the yellow. Pin 1 is orange, 10 is yellow, and 5 in pink, and I see those clearly.
In the pics I don't see the right angle to tell if the Pin 6 blue wire (CCS) is there. It should go 5-pink, 6-blue, and 7-brown. |
05-02-2009, 08:25 PM | #186 |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
As for the clutch switch wiring. At the ECM it is pin 56 of Connector C20. From there is connects through pin 14 of CA1 (the right rear connector in the under hood fuse box). It is a blue wire - shown below (For AT, two wires come into the one pin). For your test, you can jumper it to the white wire, two pins to the right of it.
Clutch Switch Wire.jpg |
05-02-2009, 09:23 PM | #187 |
My R1 eats my Vitz!!
Drives: '07 Vitz Lifty, Stick Shift Join Date: May 2007
Location: Oneida, NY
Posts: 131
|
How you guys can read that diagram...I don't know, but thank god you can :) Thanks so much! You guys are awesome! I lost the last of my light though, so tomorrow I'm gunna finish this up and we'll see how it works. I'll take some more pictures as I splice and dice, just to kinda help with someone's DIY (I'm not gunna write one up...not a very good public speaker).
__________________
My Car Rules! |
05-02-2009, 09:37 PM | #188 |
My R1 eats my Vitz!!
Drives: '07 Vitz Lifty, Stick Shift Join Date: May 2007
Location: Oneida, NY
Posts: 131
|
Well I just checked and I have no blue wire in slot 6...I have a blue wire in slot 15 though. That's on the top part, and on the bottom, I can't see under it right now to look for a wire, but when I unplug it and look in at the metal pins, there isn't one where that blue wire in slot 15 should be and there isn't one in slot 6. I hope I'm explaining this ok for now, until I can take more pics tomorrow. Is it possible there is a wire going into the harness, but there's no metal pin for the plug part? I dunno I'll check tomorrow when I don't have to use a flashlight :)
__________________
My Car Rules! |
05-02-2009, 09:51 PM | #189 | |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Quote:
|
|
05-02-2009, 09:53 PM | #190 |
My R1 eats my Vitz!!
Drives: '07 Vitz Lifty, Stick Shift Join Date: May 2007
Location: Oneida, NY
Posts: 131
|
So that means I can't do this huh?
__________________
My Car Rules! |
05-02-2009, 10:00 PM | #191 |
My R1 eats my Vitz!!
Drives: '07 Vitz Lifty, Stick Shift Join Date: May 2007
Location: Oneida, NY
Posts: 131
|
I'm guessing there's a pin in the ECM at slot 40 for the cruise, but no wire on the plastic connector part. I wonder how hard it would be to just insert a wire on the connector. I'll have to see how the wires are in there and if you can get one of those little metal pins and attatch a wire to it.
__________________
My Car Rules! |
05-02-2009, 10:03 PM | #192 |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
|
05-02-2009, 10:10 PM | #193 |
My R1 eats my Vitz!!
Drives: '07 Vitz Lifty, Stick Shift Join Date: May 2007
Location: Oneida, NY
Posts: 131
|
Is your 07 the same PK198105? I wonder if you have the wiring under the dash unlike mine. If not, what would you do? Say oh well, hang up the towel? I really want this cruise cause I drive to work back and forth about 45 mins each way. It would be really helpful. I mean I'm pretty confident in my wiring abilities. Solder, heat shrink, etc. But of course I don't wanna fuck anything up so bad my dash is gunna end up like that guys in Australia I saw on here today.
__________________
My Car Rules! |
05-03-2009, 12:59 AM | #194 |
My R1 eats my Vitz!!
Drives: '07 Vitz Lifty, Stick Shift Join Date: May 2007
Location: Oneida, NY
Posts: 131
|
Cool. Well we'll see tomorrow then.
__________________
My Car Rules! |
05-03-2009, 11:33 AM | #195 | |
My R1 eats my Vitz!!
Drives: '07 Vitz Lifty, Stick Shift Join Date: May 2007
Location: Oneida, NY
Posts: 131
|
Quote:
__________________
My Car Rules! |
|
05-03-2009, 12:27 PM | #196 | |
Drives: Black HB Join Date: Oct 2008
Location: AK
Posts: 542
|
Quote:
get a hammer. that might help. j/k j/k. dont really do that.
__________________
|
|
05-03-2009, 12:43 PM | #197 | |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Quote:
The black wire is just a +12V source that flows through the clutch switch to the ECM input. The A25 connector is a nighmare to get at, so the white wire, I said to jump the blue to, is a much easier to get at alternative to the black wire in A25. |
|
05-03-2009, 01:57 PM | #198 |
Drives: '07 Yaris HB Join Date: Apr 2006
Location: Sudbury, Canada
Posts: 520
|
I ended up getting it off ... I meant using the torque wrench as a breaker bar of sorts to give me leverage... and it worked.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag | CTScott | DIY / Maintenance / Service | 307 | 04-04-2023 03:43 AM |
DIY Cruise Control on 07-08 Yaris (step by step) | Vince87 | DIY / Maintenance / Service | 431 | 12-28-2020 01:37 AM |
Cruise Control - Again! | CB900F2 | DIY / Maintenance / Service | 47 | 06-17-2010 06:29 PM |
Cruise control vs MPG | YarisOwnersDad | Fuel Economy Forum | 15 | 05-29-2009 03:55 PM |
Using Cruise control | Driver | General Yaris / Vitz Discussion | 14 | 11-09-2006 10:12 PM |