![]() |
![]()
![]() |
![]() |
#19 |
![]() ![]() ![]() Drives: 08 Yaris 3 Door Hatchback Join Date: Aug 2019
Location: ‘Murica!
Posts: 453
|
DAMN! I'm jelly... you even did the 5th gear swap that I had planned on doing. Where'd you get them headlights!!!
![]() ![]() ![]() |
![]() |
![]() |
![]() |
#20 |
Gen 3 > Gen 2
Drives: NCP131, F-150 Join Date: Jul 2019
Location: Red Deer, AB
Posts: 501
|
They look like projector retrofitted OEM lights.
__________________
2014 NCP131 5 Speed 2007 F150 4.2L 5 Speed 2013 Rav4 LE AWD Autotragic - Wife's ![]() |
![]() |
![]() |
![]() |
#21 |
![]() ![]() ![]() Drives: 08 Yaris 3 Door Hatchback Join Date: Aug 2019
Location: ‘Murica!
Posts: 453
|
|
![]() |
![]() |
![]() |
#22 |
![]() ![]() Drives: '07 Yaris Liftback Join Date: Jul 2007
Location: Bay Area, CA
Posts: 41
|
Yup! Morimoto M LED 2.0 projectors in the stock housing. Wanted that OEM+ look
|
![]() |
![]() |
![]() |
#23 |
![]() ![]() ![]() Drives: 2007 Toyota Yaris 3 door Join Date: Sep 2018
Location: Arizona
Posts: 405
|
was the differential preload in spec? or did you have to change out the shim? im curious as to how to remove the bearings in the case
|
![]() |
![]() |
![]() |
#24 | |
![]() ![]() Drives: '07 Yaris Liftback Join Date: Jul 2007
Location: Bay Area, CA
Posts: 41
|
Quote:
Unless you have a very large press, I used a deadblow with an appropriately sized socket to push the old bearings out. |
|
![]() |
![]() |
![]() |
#25 |
![]() ![]() ![]() Drives: 2007 Toyota Yaris 3 door Join Date: Sep 2018
Location: Arizona
Posts: 405
|
gotcha gotcha, did you also fp the input shaft bearing and that front seal?
|
![]() |
![]() |
![]() |
#26 |
![]() ![]() Drives: '07 Yaris Liftback Join Date: Jul 2007
Location: Bay Area, CA
Posts: 41
|
|
![]() |
![]() |
![]() |
#27 |
![]() ![]() Drives: '07 Yaris Liftback Join Date: Jul 2007
Location: Bay Area, CA
Posts: 41
|
BAR Referee - California Smog Certification
To legally drive the car and register it in California, the engine change must be certified by the Bureau of Automotive Repair or BAR. This is a two part process which certifies that the engine change meets all emissions requirements. The first part involves checking that all documentation is correct and that the car has been prepared per the engine change guidelines. The second part involves a physical inspection of the engine change by a BAR referee and smog check. Part One - Phone Interview After scheduling a phone appointment with the BAR office, a BAR rep will call for a 50 minute interview to discuss the engine change. They will confirm that you understand the guidelines (https://www.bar.ca.gov/consumer/smog...engine-changes) and ask if you have any questions about the process. They will also ask you to email the following details:
*Most off the shelf scan tools can produce this (usually under a vehicle info screen or similar), however if you do take it to a shop you will need to explain what you need. This step confirms the ECM has not been tampered with and the programming matches a smog legal one. Upon confirmation of the above, the BAR rep will have you contact the BAR office again to schedule your in-person inspection. Part Two - In-person Inspection Once the inspection is scheduled, you'll receive details on what BAR Referee location to go to and what you'll need. Generally, they will ask you to arrive a few minutes early. They will then take your car in to inspect the engine change and also perform a rolling road smog check. The process can take up to two hours, so be prepared with plenty of fuel, oil, and coolant. They do charge for the smog check ($8.25 in 2023). Assuming everything was followed correctly and the car blows clean an engine change sticker will be applied to the car by the BAR referee, either in the engine bay or door jamb. ![]() And that's it! The car can now be registered and driven legally on California streets. |
![]() |
![]() |
![]() |
#28 |
Gen 3 > Gen 2
Drives: NCP131, F-150 Join Date: Jul 2019
Location: Red Deer, AB
Posts: 501
|
California is whack.
In Alberta its like: "oh you have an car and it has insurance? its roadworthy"
__________________
2014 NCP131 5 Speed 2007 F150 4.2L 5 Speed 2013 Rav4 LE AWD Autotragic - Wife's ![]() |
![]() |
![]() |
![]() |
#29 |
![]() ![]() ![]() Drives: 2007 Toyota Yaris 3 door Join Date: Sep 2018
Location: Arizona
Posts: 405
|
how do you like the helical limited slip diff?
|
![]() |
![]() |
![]() |
#30 |
![]() ![]() Drives: '07 Yaris Liftback Join Date: Jul 2007
Location: Bay Area, CA
Posts: 41
|
|
![]() |
![]() |
![]() |
#31 |
![]() ![]() ![]() Drives: 2007 Toyota Yaris 3 door Join Date: Sep 2018
Location: Arizona
Posts: 405
|
i bought a quaife diff, going to try it, its basically a helical style but a little different operating principle, i have had a really bad clunk with the cusco 1.5 diff and it snapped my passenger axle in half from the vibration and shock it was outputting, i got a whole another trans i pulled apart and serviced with new oem seals and changed out 2nd and 3rd gear synchros and hubs as they were really boogered up looking. all the bearings looked basically like new with no scratches or scoring at all so im gonna reuse them
|
![]() |
![]() |
![]() |
#32 | |
![]() ![]() Drives: '07 Yaris Liftback Join Date: Jul 2007
Location: Bay Area, CA
Posts: 41
|
Quote:
![]() |
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Toyota Echo Trans Swap (Auto -> Man) | es604 | Performance Modifications | 2 | 07-29-2022 08:03 PM |
Manual To Auto | bronsin | General Yaris / Vitz Discussion | 10 | 12-22-2008 10:32 PM |
Manual vs. Auto | littlecarlove | General Yaris / Vitz Discussion | 25 | 10-25-2006 08:45 PM |