ECU Wiring Diagram? - Toyota Yaris Forums

thebarber · 09-21-2009, 01:00 PM

anyone have the ecu diagram for an 07 yaris hatch? searched, but can't find it...

BLH · 09-21-2009, 01:12 PM

Closest I have seen is in section 5 of the EWD.PDF file part of the service manual. I downloaded from a thread here.

thebarber · 09-21-2009, 01:46 PM

http://www.etimago.com/yaris/repairmanual/

thanks to etimago for this one...

CTScott · 09-21-2009, 10:35 PM

Here's a chart that I put together. The connector pinouts are at the end of the EWD. I went through the EWDs to figure out every used pin on the two connectors.

In case you are wondering about the highlighting - They are the pins needed to fire up and ECM on the bench. The ones highlighted in red are the ones that need +12V and the yellows are the ones that need to be grounded.

Yaris ECM.pdf

AlexNet0 · 09-21-2009, 10:42 PM

wow, very nice!!

*tk-421* · 09-22-2009, 03:49 AM

Well done CTScott!
Much

miketrd · 10-06-2010, 06:12 PM

Hellow all

I bought an 1nz-fet - NCP13 Vitz TRD engine with turbo from yahoo jpctrade auction.

By trying to put the motor on my car we found the following problem: The 2 sockets with wire from ecu to car speedometer are missing. I attach a photograph (111.jpg) to show the missing sockets.

So we found 2 sockets which match but we haven't the terminals of ecm (ecu pinout - wiring diagram) to construct the cables.

In addition to the above my car is Toyota Yaris TS 1.5- NCP13 2002 and the vitz trd engine is from a vitz rs turbo 2003 model (facelift). So the 2 harnesses are different.

I want to ask you someone have the pinout diagram for this or where could i find it?

Thanks in advance

sleey0 · 10-06-2010, 06:38 PM

^^

Goo luck finding that. Ouch.....

CTScott · 10-06-2010, 09:17 PM

Quote:

Originally Posted by miketrd

Hellow all

I bought an 1nz-fet - NCP13 Vitz TRD engine with turbo from yahoo jpctrade auction.

By trying to put the motor on my car we found the following problem: The 2 sockets with wire from ecu to car speedometer are missing. I attach a photograph (111.jpg) to show the missing sockets.

So we found 2 sockets which match but we haven't the terminals of ecm (ecu pinout - wiring diagram) to construct the cables.

In addition to the above my car is Toyota Yaris TS 1.5- NCP13 2002 and the vitz trd engine is from a vitz rs turbo 2003 model (facelift). So the 2 harnesses are different.

I want to ask you someone have the pinout diagram for this or where could i find it?

Thanks in advance

I think I have everything that you need. PM me your email address and I'll email you the pdf's.

sleey0 · 10-06-2010, 09:54 PM

CT just has every wring scheme imaginable!!!

You keep on surprising me:)

happyshadrack@gmail.com · 04-05-2015, 12:53 PM

Quote:

Originally Posted by CTScott

I think I have everything that you need. PM me your email address and I'll email you the pdf's.

CT please send me the same PDF. I have the same problem here with a new engine

happyshadrack@gmail.com · 04-05-2015, 12:57 PM

Quote:

Originally Posted by miketrd

Hellow all

I bought an 1nz-fet - NCP13 Vitz TRD engine with turbo from yahoo jpctrade auction.

By trying to put the motor on my car we found the following problem: The 2 sockets with wire from ecu to car speedometer are missing. I attach a photograph (111.jpg) to show the missing sockets.

So we found 2 sockets which match but we haven't the terminals of ecm (ecu pinout - wiring diagram) to construct the cables.

In addition to the above my car is Toyota Yaris TS 1.5- NCP13 2002 and the vitz trd engine is from a vitz rs turbo 2003 model (facelift). So the 2 harnesses are different.

I want to ask you someone have the pinout diagram for this or where could i find it?

Thanks in advance

please forward me the pdf from CT if you can, bought a new enine with the same problem

Kaws Wong · 09-27-2015, 11:04 PM

HI MAte,

I have the same problem also, would you please forward pdf diagram also?

Thank for your help.
BR.
Kaws

Juan Perez · 05-19-2018, 06:12 PM

does anyone have the diagram?
Could tell me where i can find it

Just build a yaris TS with turbo and need the pinout diagram for the ECU vitz turbo (1nz-fet - NCP13 Vitz TRD)

thanks

Sd2jza70 · 09-27-2019, 09:42 PM

I’m in need of the diagram for the 1NZ-FET trd Turbo ecu if anybody would be so kind as to share it :)

Huevito · 08-12-2022, 05:07 PM

In need of the diagram for the 1nz turbo also can someone help if anyone is still out there?

09-21-2009, 01:00 PM	#1
thebarber daily driver View User's Garage Drives: the #wrecho Join Date: Jun 2006 Location: Grand Rapids, MI Posts: 5,877	ECU Wiring Diagram? anyone have the ecu diagram for an 07 yaris hatch? searched, but can't find it... __________________

09-21-2009, 01:46 PM	#3
thebarber daily driver View User's Garage Drives: the #wrecho Join Date: Jun 2006 Location: Grand Rapids, MI Posts: 5,877	http://www.etimago.com/yaris/repairmanual/ thanks to etimago for this one... __________________

09-21-2009, 10:42 PM	#5
AlexNet0 View User's Garage Drives: '07 Yaris 3dr Join Date: Nov 2008 Location: Rockland, ME Posts: 1,638	wow, very nice!! __________________ ---------- MI-YW ----------

09-22-2009, 03:49 AM	#6
tk-421 Super Moderator View User's Garage Drives: 5D-07-LB Join Date: Jan 2007 Location: Dagobah Posts: 4,263	Well done CTScott! Much __________________ --[ FORUM RULES ]--[ SEARCHING TIPS ]--[ EYELIDS PICS ]--[ RBK SPOILER ]--[ BEST/WORST INVESTMENTS ]--

10-06-2010, 06:38 PM	#8
sleey0 Drives: 2008 Yaris LB Join Date: Jul 2010 Location: PA Posts: 899	^^ Goo luck finding that. Ouch..... __________________ "And that goes for any of you, never get put down from someone who gets jealous of you; build it and prove them wrong. There will always be haters and naysayers but those are also the ones who's cars are worth less than my seats." xbgod - 9/23/2010

09-21-2009, 01:12 PM	#2
BLH Drives: 2007 Yaris Sedan Join Date: Apr 2009 Location: CT Posts: 277	Closest I have seen is in section 5 of the EWD.PDF file part of the service manual. I downloaded from a thread here.

09-21-2009, 10:35 PM	#4
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	Here's a chart that I put together. The connector pinouts are at the end of the EWD. I went through the EWDs to figure out every used pin on the two connectors. In case you are wondering about the highlighting - They are the pins needed to fire up and ECM on the bench. The ones highlighted in red are the ones that need +12V and the yellows are the ones that need to be grounded. Yaris ECM.pdf

10-06-2010, 06:12 PM	#7
miketrd I've made a post! Drives: yaris ts Join Date: Oct 2010 Location: Greece Posts: 1	Hellow all I bought an 1nz-fet - NCP13 Vitz TRD engine with turbo from yahoo jpctrade auction. By trying to put the motor on my car we found the following problem: The 2 sockets with wire from ecu to car speedometer are missing. I attach a photograph (111.jpg) to show the missing sockets. So we found 2 sockets which match but we haven't the terminals of ecm (ecu pinout - wiring diagram) to construct the cables. In addition to the above my car is Toyota Yaris TS 1.5- NCP13 2002 and the vitz trd engine is from a vitz rs turbo 2003 model (facelift). So the 2 harnesses are different. I want to ask you someone have the pinout diagram for this or where could i find it? Thanks in advance

10-06-2010, 09:54 PM	#10
sleey0 Drives: 2008 Yaris LB Join Date: Jul 2010 Location: PA Posts: 899	CT just has every wring scheme imaginable!!! You keep on surprising me:) __________________ "And that goes for any of you, never get put down from someone who gets jealous of you; build it and prove them wrong. There will always be haters and naysayers but those are also the ones who's cars are worth less than my seats." xbgod - 9/23/2010

09-27-2015, 11:04 PM	#13
Kaws Wong I've made a post! Drives: NCP10 Vitz 00 Join Date: Sep 2015 Location: HKG Posts: 1	HI MAte, I have the same problem also, would you please forward pdf diagram also? Thank for your help. BR. Kaws

05-19-2018, 06:12 PM	#14
Juan Perez Drives: Yaris ts Join Date: May 2018 Location: Guatemala Posts: 2	does anyone have the diagram? Could tell me where i can find it Just build a yaris TS with turbo and need the pinout diagram for the ECU vitz turbo (1nz-fet - NCP13 Vitz TRD) thanks

09-27-2019, 09:42 PM	#15
Sd2jza70 Drives: 2005 Scion xb Join Date: Jun 2018 Location: San Marcos, CA Posts: 2	I’m in need of the diagram for the 1NZ-FET trd Turbo ecu if anybody would be so kind as to share it :)

08-12-2022, 05:07 PM	#16
Huevito Drives: 2007 Yaris Sedan Join Date: Aug 2022 Location: Eastvale, Ca Posts: 4	In need of the diagram for the 1nz turbo also can someone help if anyone is still out there?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Installing Trailer Light Harness	vandallen	DIY / Maintenance / Service	7	06-10-2024 10:06 AM
FS: Motec M4 Standalone ECU w/ Ignition Expander	Biggie™	Items for Sale by private party	6	10-20-2009 02:36 PM
Tricking the ECU to Relearn AF map	gwasabi	Performance Modifications	126	05-16-2009 06:15 PM
Wiring color code for 2008 LB?	charles nelson	DIY / Maintenance / Service	0	04-25-2009 03:56 PM
NEED TPMS Wiring Diagram please	mikenacarato	DIY / Maintenance / Service	9	02-11-2009 11:55 PM