Toyota Yaris Forums - Ultimate Yaris Enthusiast Site
 

 


 
Go Back   Toyota Yaris Forums - Ultimate Yaris Enthusiast Site > Technical Forums > DIY / Maintenance / Service
  The Tire Rack

Reply
 
Thread Tools Display Modes
Old 10-28-2009, 07:50 PM   #1
PeteZNY
 
Drives: 2009 Yaris 3 Door
Join Date: Feb 2009
Location: Long Island
Posts: 2
Cruise control install 2009 Yaris 3 door

Successfully installed factory cruise control today in a 2009 Yaris 3 door base hatch. Just want to sum up and condense what I learned from the three or four other cruise control threads and my observations.

A few points

If your 2009 Yaris has the Power Package or is the S all the correct wiring is in place. If you have a base without the power package there may be more wiring needed that is not covered here.

I know this package is more expensive then the aftermarket switches mentioned elsewhere or the Radio Shack specials which can be put together for 10 bucks but I like the stock look and think a dealer will never even notice you did this yourself if there is a warranty issue down the line.

If you have the Power Package you only need three parts for an auto or four parts for a standard shift. Those parts are:
84632-08021 Cruise control switch $100
84633-02020 Cruise switch wire $36
90159-50199 Screws (2) $2
88280-14030 Clutch switch (stick shift only) $20

You only have to remove the airbag and drill one 1 inch hole for the auto, that and install the clutch switch for the stick. Piece of cake all around and its just 20 minutes start to finish if you have all the parts and tools assembled in advance.

Tools needed:
#2 Philips screwdriver
A small blade flat screwdriver
1-inch hole saw and drill
#27 torx driver
10 mm wrench
14 mm wrench for stick
That’s all folks.

The procedure:
Use the 10 mm wrench to remove the negative terminal from the battery to disable the airbag. Wait at least 90 seconds before removing the airbag, better yet do the clutch switch first or go get a soda.

Do the clutch switch if it’s a stick. There is an under dash cover that needs to be removed, remove the two philips screws on the bottom edge of the dash and just pop the cover down. Now get under the dash and look up at the driver’s side of the clutch lever and you'll see a bolt that stops the pedal when you let the clutch up. Get a feel for how much free play the bolt is adjusted to. Use the 14 mm wrench to break the lock nut and replace that bolt with the clutch switch making sure you duplicate the free play and snug down the switches lock bolt. Now look about 7 inches above the switch you just installed and you'll see the wiring harness for it taped up to another harness. Cut it down and plug it in and put the under dash cover back.

Here are pics of the underdash cover and the clutch switch in place.



Now remove the airbag. Use the #27 torx driver on the two nuts recessed on both sides of the steering wheel loosen them until the airbag assembly is loose, you don't have to completely remove them. SUPPORT the airbag you don't want to stress the wires going into the clock spring assembly. There are three wires to remove, the horn wire and the two airbag wires. The horn wire is a spade connector - just pull it off the airbag. The airbag wires require you to first use a small flat blade screwdriver to work up the yellow clip on top of the connector when that is done then use the screwdriver under the connector to work the connector up out of the airbag. Put the airbag someplace safe out of the sun.

Here is the pic of the steering wheel with air bag removed


Now remove the horn wire from the clock spring by just pressing lightly on the tab on top and pull the wire out. Use some masking tape and secure the airbag wires aside so you don't damage them or the clock spring.

Drill the 1" hole for the switch. I just matched the switch up to the screw holes, estimated the spot then carefully drilled from the outside in. Put the switch through the hole and see if you lined up right, remember the switch is supposed to move up down and forward. Enlarge the hole as necessary to make up for alignment errors using a sharp knife then screw the switch in place.

Pics of the cruise control switch mounted.



Put your new cruise control switch wire in the connector on the clock spring you took the horn wire out of and plug it into the cruise switch. Reinstall the airbag reversing the method you used to take the connectors off. There is a lot of advice out there to keep yourself grounded while you handle the airbag, you can do this by just touching the bare metal in the steering wheel assembly its grounded. Tighten the two #27 torx bolts on either side of the wheel, reconnect the battery and you're done!

SUCCESS!
PeteZNY is offline   Reply With Quote
Old 10-28-2009, 07:53 PM   #2
blacksandiegovitz
Your mom goes to college
 
blacksandiegovitz's Avatar
 
Drives: 08 Vitz
Join Date: Oct 2008
Location: Just chillin' out brah !
Posts: 1,434
Nice write-up/ install pictures ! Kinda makes me what to install this modd along with some power windows lol .
blacksandiegovitz is offline   Reply With Quote
Old 10-28-2009, 07:58 PM   #3
schleppy
I love momentum.
 
schleppy's Avatar
 
Drives: 2009 Yaris LB, Red
Join Date: Feb 2009
Location: Boston, MA
Posts: 587
Send a message via AIM to schleppy
Nice write up!

I took the easy way out and wired up my own buttons on an empty panel. It took longer to solder up the buttons than it did to wire everything.
schleppy is offline   Reply With Quote
Old 10-28-2009, 08:13 PM   #4
PeteZNY
 
Drives: 2009 Yaris 3 Door
Join Date: Feb 2009
Location: Long Island
Posts: 2
Well my way was alot easier I think but it was far more expensive.
PeteZNY is offline   Reply With Quote
Old 11-05-2009, 09:56 PM   #5
bigapl
 
Drives: 2010 Yaris
Join Date: Nov 2009
Location: Columbus GA
Posts: 12
If you watch flea bay or your local salvage yards you can get a whole steering wheel with the parts for less that $75...
bigapl is offline   Reply With Quote
Old 11-06-2009, 12:55 AM   #6
1NZYaris1
 
1NZYaris1's Avatar
 
Drives: Yaris
Join Date: Oct 2008
Location: New Zealand
Posts: 2,566
WOW that is great . now to talk nicly to someone over there to buy it for me .lol
1NZYaris1 is offline   Reply With Quote
Old 11-06-2009, 01:56 AM   #7
H3LlIoN
 
Drives: '09 Yarrrr hatch
Join Date: Aug 2009
Location: Midatlantic
Posts: 727
Do you have the p/n for the column cover, should I not want to go drilling in to my existing piece? Thanks, killer write up.
H3LlIoN is offline   Reply With Quote
Old 11-06-2009, 02:00 AM   #8
regal
 
Drives: 09 Yaris 3 Dr White LB
Join Date: Mar 2009
Location: PA
Posts: 432
If you don't have the power package, what additional wiring is required?
regal is offline   Reply With Quote
Old 11-06-2009, 11:44 PM   #9
H3LlIoN
 
Drives: '09 Yarrrr hatch
Join Date: Aug 2009
Location: Midatlantic
Posts: 727
Quote:
Originally Posted by H3LlIoN View Post
Do you have the p/n for the column cover, should I not want to go drilling in to my existing piece? Thanks, killer write up.
Anyone have the cover p/n?
H3LlIoN is offline   Reply With Quote
Old 11-07-2009, 07:02 PM   #10
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
Quote:
Originally Posted by H3LlIoN View Post
Anyone have the cover p/n?
The part number for the one with the hole already in it is:

Cover, Steering Wheel Boss, Lower: 45184-52130-B0
CTScott is offline   Reply With Quote
Old 11-08-2009, 10:12 AM   #11
H3LlIoN
 
Drives: '09 Yarrrr hatch
Join Date: Aug 2009
Location: Midatlantic
Posts: 727
Thanks Scott
H3LlIoN is offline   Reply With Quote
Old 11-08-2009, 10:17 AM   #12
AlexNet0
 
AlexNet0's Avatar
 
Drives: '07 Yaris 3dr
Join Date: Nov 2008
Location: Rockland, ME
Posts: 1,638
Send a message via AIM to AlexNet0 Send a message via MSN to AlexNet0 Send a message via Yahoo to AlexNet0
Quote:
Originally Posted by regal View Post
If you don't have the power package, what additional wiring is required?

see here: http://www.yarisworld.com/forums/showthread.php?t=16188
__________________
----------
----------
AlexNet0 is offline   Reply With Quote
Old 01-02-2010, 06:29 AM   #13
upgradedyaris
 
Drives: Yaris & Supra
Join Date: Nov 2008
Location: Here
Posts: 118
I wonder if you can buy the panel that you cut the hole in with the cruise control already cut. 100% OEM

Duane
upgradedyaris is offline   Reply With Quote
Old 01-02-2010, 06:44 AM   #14
CTScott
ULTIMATE
 
CTScott's Avatar
 
Drives: 09 5dr LB, 2x 08 3dr LB
Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
Quote:
Originally Posted by upgradedyaris View Post
I wonder if you can buy the panel that you cut the hole in with the cruise control already cut. 100% OEM

Duane
Yes, look at post #10 above for the Toyota part number.
CTScott is offline   Reply With Quote
Old 01-02-2010, 07:23 AM   #15
1NZYaris1
 
1NZYaris1's Avatar
 
Drives: Yaris
Join Date: Oct 2008
Location: New Zealand
Posts: 2,566
the oem cruise switch and wire can be had for under
$30.00US brand new
just in case people are interested
1NZYaris1 is offline   Reply With Quote
Old 01-02-2010, 03:17 PM   #16
FunkyCole
 
FunkyCole's Avatar
 
Drives: 07 Toyota Yaris
Join Date: Jun 2007
Location: SoCal, Edwards AFB
Posts: 18
I would just like to add, Disconnect your battery before you mess with your airbag.
FunkyCole is offline   Reply With Quote
Old 01-04-2010, 03:56 PM   #17
upgradedyaris
 
Drives: Yaris & Supra
Join Date: Nov 2008
Location: Here
Posts: 118
I got my cruise for 71 bucks from dealer today! 22 for the wire. :)

So, this works automatically once you hook this all up!?!

Duane
upgradedyaris is offline   Reply With Quote
Old 01-07-2010, 02:27 PM   #18
EricGSXR
 
EricGSXR's Avatar
 
Drives: Yaris NSP90 1.33 TTE
Join Date: Jan 2010
Location: NL
Posts: 25
Is the Euro Yaris prepared for a factory cruise control and will it work?

Would be great because I've got the cruise control stick already
EricGSXR is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
NEWS: TOYOTA REVEALS ALL-NEW YARIS SEDAN AT 2006 LOS ANGELES AUTO SHOW VitzBoy General Yaris / Vitz Discussion 7 09-20-2023 07:50 AM
Cruise Control chessclubloser DIY / Maintenance / Service 11 03-27-2010 11:59 AM
2007 Yaris Pricing Info ! YarisBueller New YARIS Purchase Forum 104 06-24-2009 04:54 PM
How difficult is it to install the aftermarket cruise control kit? grampi Performance Modifications 3 07-19-2007 08:06 AM


All times are GMT -4. The time now is 02:13 AM.




YarisWorld
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.