|
02-21-2015, 10:53 PM | #1 |
Drives: 2005 Toyota Vitz RS Join Date: Jan 2012
Location: Auckland, New Zealand
Posts: 181
|
ABS problem and error codes.
I get ABS light come up sometime. I would say maybe 2 times a month. Seems to randomly come up. I can't think of any specific action I did to cause them. If I restart the car, the ABS light goes away.
So one day I was driving with my Techstream stuff. The light came on again. I pulled over and ran a scan. This is what I got: C1241, C1249 Any ideas how to fix this ? See attached image. |
02-21-2015, 11:08 PM | #2 |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Those are interesting ones:
1241: When there is an abnormality in the power supply circuit of the brake actuator (skid control ECU), the skid control ECU sets a DTC and the operation is prohibited by the fail-safe function. This DTC is set when the voltage supplied to terminal IG1 is outside the DTC detection threshold, due to abnormalities in the battery, power source circuits or charging circuits such as the alternator circuit. The fail-safe function is canceled when the voltage to terminal IG1 returns to normal. 1249: The skid control ECU detects the brake operating conditions through a signal transmitted by the stop light switch. The skid control ECU incorporates an open circuit detection circuit. This DTC is set under either of the following conditions: • An open is detected in the stop light signal input line when the stop light switch is off. • An open is detected in the stop light circuit lead to the ground when the stop light switch is off.
__________________
|
02-21-2015, 11:09 PM | #3 |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
I would start with pulling the connector on the ABS ECU and cleaning the contacts.
__________________
|
03-22-2015, 06:03 AM | #4 |
Drives: 2005 Toyota Vitz RS Join Date: Jan 2012
Location: Auckland, New Zealand
Posts: 181
|
I don't have VSC in my car. It's confusing, the yaris repair manual seems to refer to the ABS motor thing as a skid control ECU.
Does this mean I should take the connector of the ABS motor and clean the contacts? |
03-22-2015, 08:19 AM | #5 |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Yes. The ABS ECU is the skid control ECU
__________________
|
11-08-2015, 05:19 PM | #6 |
I've made a post!
Drives: 2008 Yaris 1.5L Sedan Join Date: Nov 2015
Location: Missouri
Posts: 1
|
Thank you. I have those same codes (and more, below! :-) Can you recommend a good/best value code reader and what is the source for your code descriptions, CTScott?
I recently replaced my battery and had done my rear drum brakes myself a few months ago. My total set is: P1801, recent clutch replacement perhaps and mechanic didn't reset. At 122K miles. B1660 B1801 C0210 C1238 C1241 C1249 |
11-08-2015, 08:04 PM | #7 | |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Quote:
For code info, I get the details from the the service manual.
__________________
|
|
01-26-2016, 12:21 AM | #8 |
Drives: 2005 Toyota Vitz RS Join Date: Jan 2012
Location: Auckland, New Zealand
Posts: 181
|
I got around and cleaned up the ABS ECU connectors. Hoped the problem would go away. It came back the otherday. What do you recommend I do next ?
|
01-16-2017, 07:56 AM | #9 |
Drives: Toyota Vitz Join Date: Jan 2016
Location: Pakistan
Posts: 2
|
@CTScott
I am currently facing Vibration issue with my Vitz 2009 model. When i scanned my car with Toyota Techstream software following error code are showing in current. I don't know its related to vibration or not?. Can you tell me what are these error code means and what can be the problem of these error codes. Currently I am facing vibration on low rpm during brake operation when engine is hot and RPM drop down below 700 that cause it to vibrate on pressing accelerator vibration are gone are these error code related to this problem? -RKBladeX |
01-16-2017, 07:10 PM | #10 | |
ULTIMATE
Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008
Location: USA, CT
Posts: 13,460
|
Quote:
__________________
|
|
01-23-2017, 07:36 AM | #11 |
Drives: 01 Yaris TS Join Date: Jan 2017
Location: Athens Greece
Posts: 92
|
Hello !
Check the condition of your battery and battery terminals. Should be 12,6 at rest with no surface charge. U0100 is lost com due to voltage droping under 7V and loosing com with the control unit. During ABS activation the ABS pump motor draws a lot of current and with a weak battery and or weak connections you could be experiencing c1249. |
02-27-2017, 01:26 PM | #12 |
Drives: 2006 Yaris RS 3-Door Join Date: Feb 2016
Location: YYZ
Posts: 329
|
Over the past week, I've been getting random problems of ABS (and handbrake) warning lights coming on for around 10 minutes at a time, as well as ABS sometimes kicking in when slowing down to a stop in perfectly dry road conditions. I took it to my mechanic today, and he tried cleaning the contacts, but that didn't help, and he now has the ABS error showing constantly.
He says I should change the bearing for the wheel with the snsor problem, as the ABS sensor is embedded in the bearing - preferably both bearings while at it. This starts to become an expensive job. He's a very good mechanic that I've known for some years, who always tell me if I can avoid changing parts that don't really need to be replaced and has saved me a lot of money of the years. So I usually tend to trust his judgment. What do the experts on this forum think? Should I change both bearings or just the one? |
02-27-2017, 03:57 PM | #13 |
1NZ-6spd
Drives: '05 6-Spd Vitz RS Join Date: Oct 2008
Location: Oshawa, Ontario, Canada
Posts: 2,967
|
Are codes coming up related to the rear sensors only?
Has he blown off the front sensors with compressed air to remove any iron buildup on the magnetic pickup? |
02-27-2017, 07:42 PM | #14 |
Drives: 07 5dr Join Date: Nov 2015
Location: YYC
Posts: 197
|
You can read the ABS codes yourself by jumping pins 4 and 13 of the OBD2 port and turning the ignition to ON. That will give you some direction if the front sensors are the issue.
|
Tags |
abs, c1241, c1249 |
|
|