Part numbers for D10/D11 pins? - Toyota Yaris Forums

CrankyOldMan · 07-22-2011, 10:47 PM

Hopefully CTScott has this info handy! I'm trying to make a harness for the DPS module and can't find anything about the pins for plugs D10 and D11. I ran the 5-digit part numbers on the plugs through toyotapartszone and found them, but there's no indication of the pins themselves online or in either the EWD or A/V repair manuals. The sockets will be from an aftermarket stereo adapter, and I have part numbers for the DPS end.

From a post I just read about someone who tried to order pins for D75/D79, it's cost prohibitive to get OEM pins ($12 EACH!), so any tips on secondary sources would be great. Speaking of D79, I don't even see it listed in the '07 EWD...

CTScott · 07-22-2011, 11:09 PM

Are you looking for pins to add to the D10 and D11 connectors, or pins to plug into the pins in the existing connectors?

CrankyOldMan · 07-23-2011, 08:07 AM

Sorry for the confusion. I'm looking for the pins that mount in the D10/11 connectors. I basically need to replicate the existing plugs on a new wire harness. Maybe a diagram would be useful?

The "new" D10/11 plugs are the only part that I can't get the internal pins for at the moment.

Thanks!

CTScott · 07-23-2011, 09:59 AM

Quote:

Originally Posted by CrankyOldMan

Sorry for the confusion. I'm looking for the pins that mount in the D10/11 connectors. I basically need to replicate the existing plugs on a new wire harness. Maybe a diagram would be useful?

The "new" D10/11 plugs are the only part that I can't get the internal pins for at the moment.

Thanks!

I have lots of those pins. Let me know how many you need and I'll give you a good price for the whole lot.

CrankyOldMan · 07-23-2011, 11:21 AM

By "good price" are you talking relative to the OEM price for the D74 connectors ($10+), or relative to some common pins from Mouser/DigiKey ($0.10+)?

The other thought I had was to find a local junker with the same radio plugs and cannibalize it. Since I'll be crimping the pins for the DPS connector on the other end of the wires, they can be pre-made, and it saves me the hassle of ordering the connector bodies online.

CTScott · 07-23-2011, 04:16 PM

Quote:

Originally Posted by CrankyOldMan

By "good price" are you talking relative to the OEM price for the D74 connectors ($10+), or relative to some common pins from Mouser/DigiKey ($0.10+)?

The other thought I had was to find a local junker with the same radio plugs and cannibalize it. Since I'll be crimping the pins for the DPS connector on the other end of the wires, they can be pre-made, and it saves me the hassle of ordering the connector bodies online.

Good like way less than the OEM price, but a bit more than digikey (since they are not off the shelf pins, but rather Toyota custom ones made by Sumitomo or AMP). I could probably do about $10 shipped for the two connectors worth.

The wrecker option is good. Also, there are aftermarket ones that are sold for installing a Toyota radio in something else. They run about $10.

CrankyOldMan · 07-23-2011, 05:14 PM

My original idea was to scour mouser and digikey for them (since I've found other automotive connectors on them) but without a product line or manufacturer part number I've been stumped.

The Toyoya (Fujitsu ten)->other harness would be a great idea too. I'll see what I can come up with and let you know if I need the pins. Thanks again for your help.

CrankyOldMan · 07-23-2011, 05:23 PM

Here's one for the tC OEM stereo:

http://www.amazon.com/Stereo-Harness...452485&sr=1-93

I'm not sure if the picture is accurate, or if all of the pins are included, but it /looks/ promising.

Lil Abner · 07-23-2011, 05:53 PM

Actually, here's a better price:
http://cgi.ebay.com/ebaymotors/ws/eB...3154&viewitem=

I just got one of those a week ago, and it's great quality. Is that what you're looking for? Oh, and I did use that exact seller. Shipping was quick from California.

CrankyOldMan, what part of West Michigan you from?

CrankyOldMan · 07-23-2011, 07:25 PM

Quote:

Originally Posted by Lil Abner

Actually, here's a better price:
http://cgi.ebay.com/ebaymotors/ws/eB...3154&viewitem=

I just got one of those a week ago, and it's great quality. Is that what you're looking for? Oh, and I did use that exact seller. Shipping was quick from California.

CrankyOldMan, what part of West Michigan you from?

Sweet! I grabbed both the OEM and aftermarket harnesses so that all I have to do is crimp the pins on the other end for the DPS.

I'm from the greater Grand Rapids/Grand Haven area. Perhaps you've seen me driving like I own an Audi? =)

CTScott - I'm gonna pass on the pins for now. If it looks like I need to re-wire with longer wire I'll give you a PM.

Thank you both for your help!

Lil Abner · 07-23-2011, 07:29 PM

I actually live in Holland, and go to Kalamazoo a few times a week. I stay on M40/89 most of the time. Always fun seeing more Yaris' in the area!

Awesome you got those. We'll be looking forward to your progress. Let us know if you've got anymore questions, or need a hand.

CrankyOldMan · 07-26-2011, 01:21 PM

CTScott - by any chance are these connectors the Sumitomo MT non-sealed line? http://easternbeaver.com/Main/Elec__...onnectors.html
Scroll to the bottom...

Lil Abner - I don't usually get south of Port Sheldon, but occasionally go out that way for shopping.

CTScott · 07-26-2011, 02:01 PM

Quote:

Originally Posted by CrankyOldMan

CTScott - by any chance are these connectors the Sumitomo MT non-sealed line? http://easternbeaver.com/Main/Elec__...onnectors.html
Scroll to the bottom...

Close, but not quite. The male has the tabs in the wrong direction and the female is missing the two tabs.

CrankyOldMan · 07-26-2011, 04:38 PM

Quote:

Originally Posted by CTScott

Close, but not quite. The male has the tabs in the wrong direction and the female is missing the two tabs.

Are you looking at the ones on the bottom half of the page? The top half (HM series) are very much incorrect, but the bottom half looks like they might fit. The photos on this site are pretty crappy resolution and low contrast, but it's the closest thing I've been able to find so far.

6-pos MT series

10-pos MT series

The polarizing rib channels are both present (the OEM only uses one) but that doesn't matter in this case since they're going into the OEM stereo. The female sockets however won't work on the OEM wire harness unless one of the ribs is removed.

CTScott · 07-26-2011, 04:46 PM

This is what the correct ones look like from the side. Note how the male pin has the ribs on the opposite side and the female has them, but the pins above do not. The pins above may work, but my experience with various other Toyota pins is that even though they look mighty close, they end up not working. Either they won't insert all of the way in, or the pin lock won't snap back into place.

D10-D11 Pins.jpg

CrankyOldMan · 07-26-2011, 05:10 PM

Quote:

Originally Posted by CTScott

This is what the correct ones look like from the side. Note how the male pin has the ribs on the opposite side and the female has them, but the pins above do not.

Oh, I see now. I thought you were talking about the housings, not the pins. Crap, now I'm back at square 1 with finding the original manufacturer. I've checked out Molex, Amp/Tyco and Sumitomo. I can't think of anyone else who might have made them aside from Denso themselves, but their website doesn't seem to have any info on just the connectors.

Maybe it's just more worthwhile to stick with the premade harnesses?

CrankyOldMan · 07-27-2011, 11:43 PM

Ok, wire harnesses showed up today. The quality of the plastic and pins is marginal, but I'm almost certain that they are a knockoff of the MT series. If this seems to be a decent upgrade and I outright buy the DPS, I intend to get the OEM connector bodies and a set of pins from CTScott.

Got started on the new DPS harness but have hit a few snags. It's too dark to go out to the car and pull the HU now, but I think there are some unneeded wires on the pin harnesses and not enough wires on the socket harnesses. Pics (this weekend?) once things are sorted out.

plug for D10

Pins 8 and 9 aren't shown in the EWD and are labeled "POWER ANTENNA" and "ANT TURN-ON (12V+)" on the new D10 connector. The aftermarket harness has pin 8 jumped to pin 9, and pin 9 is labeled "POWER ANTENNA". Since the eggmobile has a fixed antenna, and doesn't adjust the length of it when you change channels (*ahem-LEXUS*), I'm thinking that these can be removed safely. I will verify if there is in fact a wire connected to it tomorrow-ish.

plug for D11

Pin 4 (the dot) is only present on the new D11 connector and is labeled "DIMMER GROUND". This will need to be connected to the OEM harness to control backlighting, yes? There isn't a wire on the male pin connector to match, but I may just cannibalize the "power antenna" wires.

CTScott · 07-27-2011, 11:52 PM

Quote:

Originally Posted by CrankyOldMan

Ok, wire harnesses showed up today. The quality of the plastic and pins is marginal, but I'm almost certain that they are a knockoff of the MT series. If this seems to be a decent upgrade and I outright buy the DPS, I intend to get the OEM connector bodies and a set of pins from CTScott.

Got started on the new DPS harness but have hit a few snags. It's too dark to go out to the car and pull the HU now, but I think there are some unneeded wires on the pin harnesses and not enough wires on the socket harnesses. Pics (this weekend?) once things are sorted out.

plug for D10

Pins 8 and 9 aren't shown in the EWD and are labeled "POWER ANTENNA" and "ANT TURN-ON (12V+)" on the new D10 connector. The aftermarket harness has pin 8 jumped to pin 9, and pin 9 is labeled "POWER ANTENNA". Since the eggmobile has a fixed antenna, and doesn't adjust the length of it when you change channels (*ahem-LEXUS*), I'm thinking that these can be removed safely. I will verify if there is in fact a wire connected to it tomorrow-ish.

plug for D11

Pin 4 (the dot) is only present on the new D11 connector and is labeled "DIMMER GROUND". This will need to be connected to the OEM harness to control backlighting, yes? There isn't a wire on the male pin connector to match, but I may just cannibalize the "power antenna" wires.

The Yaris actually has a powered antenna (amplified). Pin 8 is the feed from the radio to the antenna amplifier. Pin 9 is not used on the OEM radio.

Pin 4 on D11 is not used on the Yaris.

07-22-2011, 10:47 PM	#1
CrankyOldMan 2ZR swap. DO IT! Ask how! View User's Garage Drives: 09 Meteoric Metallic HB Join Date: Feb 2011 Location: West Michigan Posts: 2,333	Part numbers for D10/D11 pins? Hopefully CTScott has this info handy! I'm trying to make a harness for the DPS module and can't find anything about the pins for plugs D10 and D11. I ran the 5-digit part numbers on the plugs through toyotapartszone and found them, but there's no indication of the pins themselves online or in either the EWD or A/V repair manuals. The sockets will be from an aftermarket stereo adapter, and I have part numbers for the DPS end. From a post I just read about someone who tried to order pins for D75/D79, it's cost prohibitive to get OEM pins ($12 EACH!), so any tips on secondary sources would be great. Speaking of D79, I don't even see it listed in the '07 EWD...

07-22-2011, 11:09 PM	#2
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	Are you looking for pins to add to the D10 and D11 connectors, or pins to plug into the pins in the existing connectors? __________________

07-23-2011, 08:07 AM	#3
CrankyOldMan 2ZR swap. DO IT! Ask how! View User's Garage Drives: 09 Meteoric Metallic HB Join Date: Feb 2011 Location: West Michigan Posts: 2,333	Sorry for the confusion. I'm looking for the pins that mount in the D10/11 connectors. I basically need to replicate the existing plugs on a new wire harness. Maybe a diagram would be useful? The "new" D10/11 plugs are the only part that I can't get the internal pins for at the moment. Thanks! Last edited by CrankyOldMan; 07-23-2011 at 08:39 AM.

07-26-2011, 04:46 PM	#15
CTScott ULTIMATE View User's Garage Drives: 09 5dr LB, 2x 08 3dr LB Join Date: Oct 2008 Location: USA, CT Posts: 13,460	This is what the correct ones look like from the side. Note how the male pin has the ribs on the opposite side and the female has them, but the pins above do not. The pins above may work, but my experience with various other Toyota pins is that even though they look mighty close, they end up not working. Either they won't insert all of the way in, or the pin lock won't snap back into place. D10-D11 Pins.jpg __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Part Number(s) for '09 5-door LB engine air filter?	IsLNdbOi	DIY / Maintenance / Service	5	01-02-2011 02:51 PM
2008 OEM S model Liftback Lip kit Part numbers	PETERPOOP	Cosmetic Modifications (Exterior/Interior)	17	07-26-2010 02:33 PM
need part numbers please help?!	kid chino	General Yaris / Vitz Discussion	5	10-27-2009 03:27 AM
Rubber weatherstripping part numbers	The Spectacle	Cosmetic Modifications (Exterior/Interior)	6	05-13-2009 07:40 PM
Help Finding part numbers PLZZZZ!!!	Duckywitbigfeetz	Cosmetic Modifications (Exterior/Interior)	0	07-29-2006 03:21 AM

07-23-2011, 11:21 AM	#5
CrankyOldMan 2ZR swap. DO IT! Ask how! View User's Garage Drives: 09 Meteoric Metallic HB Join Date: Feb 2011 Location: West Michigan Posts: 2,333	By "good price" are you talking relative to the OEM price for the D74 connectors ($10+), or relative to some common pins from Mouser/DigiKey ($0.10+)? The other thought I had was to find a local junker with the same radio plugs and cannibalize it. Since I'll be crimping the pins for the DPS connector on the other end of the wires, they can be pre-made, and it saves me the hassle of ordering the connector bodies online.

07-23-2011, 05:14 PM	#7
CrankyOldMan 2ZR swap. DO IT! Ask how! View User's Garage Drives: 09 Meteoric Metallic HB Join Date: Feb 2011 Location: West Michigan Posts: 2,333	My original idea was to scour mouser and digikey for them (since I've found other automotive connectors on them) but without a product line or manufacturer part number I've been stumped. The Toyoya (Fujitsu ten)->other harness would be a great idea too. I'll see what I can come up with and let you know if I need the pins. Thanks again for your help.

07-23-2011, 05:23 PM	#8
CrankyOldMan 2ZR swap. DO IT! Ask how! View User's Garage Drives: 09 Meteoric Metallic HB Join Date: Feb 2011 Location: West Michigan Posts: 2,333	Here's one for the tC OEM stereo: http://www.amazon.com/Stereo-Harness...452485&sr=1-93 I'm not sure if the picture is accurate, or if all of the pins are included, but it /looks/ promising.

07-23-2011, 05:53 PM	#9
Lil Abner Drives: 2009 3dr LB Manual Join Date: Mar 2010 Location: Dublin, Ohio Posts: 412	Actually, here's a better price: http://cgi.ebay.com/ebaymotors/ws/eB...3154&viewitem= I just got one of those a week ago, and it's great quality. Is that what you're looking for? Oh, and I did use that exact seller. Shipping was quick from California. CrankyOldMan, what part of West Michigan you from?

07-23-2011, 07:29 PM	#11
Lil Abner Drives: 2009 3dr LB Manual Join Date: Mar 2010 Location: Dublin, Ohio Posts: 412	I actually live in Holland, and go to Kalamazoo a few times a week. I stay on M40/89 most of the time. Always fun seeing more Yaris' in the area! Awesome you got those. We'll be looking forward to your progress. Let us know if you've got anymore questions, or need a hand.

07-26-2011, 01:21 PM	#12
CrankyOldMan 2ZR swap. DO IT! Ask how! View User's Garage Drives: 09 Meteoric Metallic HB Join Date: Feb 2011 Location: West Michigan Posts: 2,333	CTScott - by any chance are these connectors the Sumitomo MT non-sealed line? http://easternbeaver.com/Main/Elec__...onnectors.html Scroll to the bottom... Lil Abner - I don't usually get south of Port Sheldon, but occasionally go out that way for shopping.

07-27-2011, 11:43 PM	#17
CrankyOldMan 2ZR swap. DO IT! Ask how! View User's Garage Drives: 09 Meteoric Metallic HB Join Date: Feb 2011 Location: West Michigan Posts: 2,333	Ok, wire harnesses showed up today. The quality of the plastic and pins is marginal, but I'm almost certain that they are a knockoff of the MT series. If this seems to be a decent upgrade and I outright buy the DPS, I intend to get the OEM connector bodies and a set of pins from CTScott. Got started on the new DPS harness but have hit a few snags. It's too dark to go out to the car and pull the HU now, but I think there are some unneeded wires on the pin harnesses and not enough wires on the socket harnesses. Pics (this weekend?) once things are sorted out. plug for D10 Pins 8 and 9 aren't shown in the EWD and are labeled "POWER ANTENNA" and "ANT TURN-ON (12V+)" on the new D10 connector. The aftermarket harness has pin 8 jumped to pin 9, and pin 9 is labeled "POWER ANTENNA". Since the eggmobile has a fixed antenna, and doesn't adjust the length of it when you change channels (ahem-LEXUS), I'm thinking that these can be removed safely. I will verify if there is in fact a wire connected to it tomorrow-ish. plug for D11 Pin 4 (the dot) is only present on the new D11 connector and is labeled "DIMMER GROUND". This will need to be connected to the OEM harness to control backlighting, yes? There isn't a wire on the male pin connector to match, but I may just cannibalize the "power antenna" wires.